Steve Bergen // Engineering Journal
Other journals: Ben | George | Scott |
[ Week 1 | 2 | 3 | 4 | 5 | 6 | 7 | 8 | 9 | 10 | 11 | 12 | 13 | 14 | 15 ]
Date of Work (2007) | Time Spent | Description |
Week 1 | ||
|
2 hours |
Selected & organized group, decided on name "insomnia design." Declared project name as "Prism." Began initial research on which parts would be necessary. |
|
1 hour |
Decided on Atmega16, MAX7313 LED drivers, and tricolor LEDs, other parts, etc. |
|
1.5 hours |
Began work on the circuit board. Completed initial consultation. |
Week 2 | ||
|
2 hours |
Continued work on circuit board. Researched more on Atmega16 chip. |
|
3 hours |
Continued work on circuit board. |
Week 3 | ||
|
2 hours |
Continued work on circuit board. |
|
3 hours |
Continued work on circuit board. |
Week 4 | ||
|
2 hours |
Worked on Engineering Journal. Researched MX7313 LED driver chip. |
|
3 hours |
Continued work on the schematics and on the circuit board. |
Week 5 | ||
|
1 hour |
Worked on the schematics and on the circuit board. |
|
2 hours |
Worked on the schematics and on the PCB. |
|
3 hours |
Worked on the LED PCB. Found out that there is no need for resistor packs. Removed res. packs from schematics and PCB. Tried to auto route the PCB but it failed conections. Changed position of headers. |
|
1 hour |
Auto routed PCB. |
Week 6 | ||
|
2 hours |
Cleaned up auto-route of PCB. |
|
3 hours |
Discussed with Craig Maynard about routing the PCB board. Talked with George on a better way to route the LED board. Started rearranging the LEDs into a more consistant view. |
Week 7 | ||
|
2 hours |
Made each group of 16 LEDs into a 4x4 shape for easy routing. Routed one group of 16 LEDs into a header, then copy pasted the rest of the LED groups. Submitted it to Craig maynard for fabrication. |
|
3 hours |
Made changed to the LED board changed the ground to a +5. Re submitted it to Craig Maynard. Started to finish work on the microprocessor schemactic. Dicussed with Dylan Sanders how to connect the DE-9 connector. |
Week 8 | ||
|
2 hours |
Continued work on the DE-9 connector. Helped George with serial inertfacing. |
|
1 hour |
Started work on the Microporocessor PCB. |
|
3 hours |
Worked on the Microprocessor PCB. Helped George with Serial inertfacing. |
Week 9 | ||
|
2 hours |
Worked on the Microprocessor PCB, placing footprints and laying down traces. |
|
3 hours |
Continued work on Microprocessor and placing traces on PCB. Created schematic library symbol and footprint for the MAX233 chip. |
|
1 hour |
Worked on interfacing MAX233 chip on schematic sheet. |
Week 10 | ||
|
3 hours |
Continued soldering LEDs and Headers on LED PCB. Discovered that we need to trim the headers down because they won't fit beside each other. |
|
3 hours |
Trimmed down the Headers to fit into the LED PCB. Continued soldering the Headers. Tested the Headers and the LEDs, replaced three that did not work. Sent the Microporcessor PCB to Craig Maynard for manufacturing. |
Week 11 | ||
|
3 hours |
Recieved Microporcessor PCB. Discovered a few errors on the board due to my error: the Atmega16 footprint was the wrong size, too small; the footprint for the DE-9 connector was incorrect, it will be easy to fix; will have to trim the Headers to fit into the board. |
Week 12 | ||
|
2 hours |
Trimmed down the Headers to fit into the Microprocessor PCB. Finished soldering the Microprocessor PCB; three resistors, Atmega16 header, and the 16 pin headers. |
|
3 hours |
Gave the Microprocessor PCB an alcohol bath to clean off the flux residue. Started designing the PRISM chassis, will be made from aluminum. |
|
1 hour |
Wrote down items, in a list, that could be wrong with the PCB. |
Week 13 | ||
|
3 hours |
Troubleshooting the Prism. |
|
3 hours |
Read AVR code. |
Week 14 | ||
|
1 hour |
Cut the pieces of aluminum to size. |
|
2 hours |
Cut and bent pieces of the aluminum case to actual shape and dimensions. |
|
3 hours |
Had Technical presentation, hardwired the LED board to show what the visualization could look like. |
Week 15 | ||
|
2 hours |
Helped out with organizing and cleaning out cupboard and other stuff to do for the business presentation. |
|
1 hour |
Final presentation. |